The right component.
In the right place.
Explore 230 references to understand the membranes, insulation and details that make up your roof.
230 products
SOPRALENE FLAM 250 GR
This roofing cap sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed by torch application. Granules protect the top surface, while the underside has a heat-fusible film.
Explore this product
Torchflex™ TP-250-Cap
Torchflex TP-250-Cap is a torch-applied SBS cap sheet. Its glass-reinforced polyester reinforcement supports waterproofing performance, while surface granules protect the bitumen from ultraviolet exposure. The underside film melts during application. It completes the roofing assemblies specified by IKO for this membrane.
Explore this product
EverGuard® TPO Smooth Membranes
EverGuard® TPO smooth-surfaced single-ply membrane for low-slope roofs. Its inherent flexibility and hot-air-weldable seams create a continuous roofing envelope. It is available in several thicknesses and colours, with attachment options selected to suit the roofing system.
Explore this product
Elastomeric - Pre-Flash™ Summum Drain 18"H
A 18-inch-high Pre-Flash™ drainage assembly combining a prefabricated drain, a cast aluminium strainer and a flow-control device with two adjustable gates. Its universal anchoring system brings the drainage detail components together. This version is intended for SBS elastomeric assemblies; membrane and dimensions are selected to suit the roofing detail.
Explore this product
SOPRALENE FLAM 180
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed by torch application. Both the top surface and the underside have a heat-fusible film. Application requirements are set out in this product’s technical documentation.
Explore this product
IKO Innovi TPO 60-mil
The Innovi TPO 60 mil membrane uses Matrix technology to resist UV exposure and weathering. Reinforced with polyester, this reflective single-ply membrane is intended for commercial roofing. It can be fully adhered or mechanically attached in accordance with specifications; IKO also includes it in its induction-welded assemblies.
Explore this product
EverGuard® TPO Extreme Smooth Membranes
Smooth TPO membrane from the EverGuard Extreme® line, designed for applications exposed to high temperatures, including roofs with solar equipment. Its formulation is designed to resist ageing, heat and UV exposure. Seams are hot-air welded, and several thicknesses allow the assembly to be tailored to the project.
Explore this product
ELASTOPHENE FLAM
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with a fibreglass mat. It is installed by torch application. Both the top surface and the underside have a polyolefin film.
Explore this product
Modiflex™ MP-180-Cap
Modiflex MP-180-Cap serves as the cap sheet in an SBS assembly or as protection for a built-up roof. Its glass-filament-reinforced polyester reinforcement is coated with modified bitumen. The granulated surface protects against UV exposure, while the sanded underside allows installation in hot asphalt or an IKO-approved cold adhesive.
Explore this product
EverGuard® TPO Fleece‑Back 100, 115, and 135 Membranes
EverGuard® TPO single-ply membrane with a fleece backing, available in 100, 115 and 135 configurations. The backing adds protection to the assembly and may allow installation over compatible existing roofs. Membrane and attachment selection depends on the substrate and the chosen assembly.
Explore this product
SOPRAFIX BASE 635
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is mechanically fastened. The top surface has a heat-fusible film, while the underside is surfaced with fine sand.
Explore this product
Modiflex™ MP-HD-Cap
Modiflex MP-HD-Cap serves as the cap sheet in an SBS assembly or as protection for a built-up roof. Its polyester and crossed glass scrim composite reinforcement is coated with modified bitumen. The granulated surface protects against UV exposure, while the sanded underside allows installation in hot asphalt or an IKO-approved cold adhesive.
Explore this product
EverGuard® SA TPO Self-Adhered Roof Membranes
EverGuard® SA TPO membrane with a factory-applied pressure-sensitive adhesive. Installation eliminates the step of applying adhesive from a pail and suits projects where solvent odours need to be limited. After the release film is removed and the membrane is rolled into place, seams are hot-air welded.
Explore this product
TPO - Pre-Flash™ Summum Drain 18"H
A 18-inch-high Pre-Flash™ drainage assembly combining a prefabricated drain, a cast aluminium strainer and a flow-control device with two adjustable gates. Its universal anchoring system brings the drainage detail components together. This version is intended for TPO assemblies; membrane and dimensions are selected to suit the roofing detail.
Explore this product
SOPRAPLY STICK TRAFFIC CAP
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed using its self-adhesive underside. Granules protect the top surface, while the underside has a two-part silicone release film.
Explore this product
Modiflex™ MF-95-SS-Base
Modiflex MF-95-SS-Base is an SBS base sheet with non-woven fibreglass reinforcement. With sanded surfaces on both sides, it is designed for fully adhered installation in hot asphalt or an IKO-approved cold adhesive. It forms part of a multi-ply roof covering in accordance with system specifications.
Explore this product
EverGuard® TPO Color Membrane
EverGuard® TPO single-ply membrane available in a range of standard and custom colours. It allows the roof to complement the building’s architectural design. Matching accessories can be specially ordered; minimum quantities and manufacturing lead times for the selected colour must be confirmed with GAF.
Explore this product
Elastomeric - Pre-Flash™ Drain 18"H
A 18-inch-high prefabricated Pre-Flash™ drain for roof drainage. The component is prepared to reduce on-site fabrication and promote a consistent finish around the drainage point. This version is intended for SBS elastomeric assemblies; membrane and dimensions are selected to suit the roofing detail.
Explore this product
SOPRALENE FLAM 180 GR
This roofing cap sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed by torch application. Granules protect the top surface, while the underside has a heat-fusible film.
Explore this product
Modiflex™ MP-180-SS-Base
Modiflex MP-180-SS-Base is an SBS base sheet with glass-filament-reinforced polyester reinforcement. With sanded surfaces on both sides, it is designed for fully adhered installation in hot asphalt or an IKO-approved cold adhesive. It forms part of a multi-ply roof covering in accordance with system specifications.
Explore this product
EverGuard® TPO Extreme Fleece-back Membranes
EverGuard Extreme® TPO membrane with an integrated polyester fleece backing. It combines the Extreme formulation for high-heat environments with a backing suited to roof recovery projects. Assembly design and attachment method must be compatible with the existing roof and project requirements.
Explore this product
SOPRASTAR FLAM GR
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed by torch application. The top surface has highly reflective granules, while the underside has a heat-fusible film. Its stated solar reflectance index is 90.
Explore this product
Modiflex™ MP-180-SS-Base (3.0 mm)
Modiflex MP-180-SS-Base (3.0 mm) is an SBS base sheet with glass-filament-reinforced polyester reinforcement. With sanded surfaces on both sides, it is designed for fully adhered installation in hot asphalt or an IKO-approved cold adhesive. It forms part of a multi-ply roof covering in accordance with system specifications.
Explore this product
EverGuard® TPO Fleece-back Membranes
EverGuard® TPO membrane with a fleece backing for single-ply roofing systems. It offers several mechanical attachment or adhesive options depending on the assembly and is suitable for certain roof recovery projects. Heat-welded seams maintain membrane continuity, while adhesive selection depends on the substrate.
Explore this product
SOPRASTAR STICK GR
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed using its self-adhesive underside. The top surface has highly reflective granules, while the underside has a two-part silicone release film. Its stated solar reflectance index is 90.
Explore this product
Modiflex™ MP-HD-SS-Base
Modiflex MP-HD-SS-Base is an SBS base sheet with polyester and crossed glass scrim composite reinforcement. With sanded surfaces on both sides, it is designed for fully adhered installation in hot asphalt or an IKO-approved cold adhesive. It forms part of a multi-ply roof covering in accordance with system specifications.
Explore this product
TPO - Pre-Flash™ Drain 18"H - Base 24″
A 18-inch-high prefabricated Pre-Flash™ drain for roof drainage. The component is prepared to reduce on-site fabrication and promote a consistent finish around the drainage point. This version is intended for TPO assemblies; membrane and dimensions are selected to suit the roofing detail.
Explore this product
SOPRAPLY STICK
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed using its self-adhesive underside. The top surface is covered with fine sand, while the underside has a silicone release film. It is also suitable for flashing applications.
Explore this product
Torchflex™ TP-180-SF-Base (3.5 mm)
Torchflex TP-180-SF-Base (3.5 mm) is an SBS base sheet with a sanded surface that helps it unroll and limits sticking within the roll. Its underside has a film that melts during torch application. This membrane can also serve as a vapour barrier, depending on the composition of the selected system.
Explore this product
SOPRAFLASH FLAM STICK
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with a fibreglass mat. It is installed using its self-adhesive underside. The top surface has a heat-fusible film, while the underside has a silicone release film. It is also suitable for flashing applications.
Explore this product
Armourbond™ 180
Armourbond 180 is a 3.0 mm self-adhered base sheet for SBS assemblies. Its polyester and glass reinforcement is coated with modified bitumen; the top surface has a microperforated film and the underside has a release liner. It can receive a torch-applied cap sheet and can be installed on flame-sensitive substrates.
Explore this product
Universal Pipe Flashing — Moulded TPO
Universal moulded TPO pipe flashing for penetrations in TPO membrane roofs. Its prefabricated shape provides a dedicated component for pipe penetrations. The stated packaging is a box of ten units; select the appropriate installation detail with the manufacturer.
Explore this product
SOPRAPLY FLAM STICK
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed using its self-adhesive underside. The top surface has a heat-fusible film, while the underside has a silicone release film. It is also suitable for flashing applications.
Explore this product
Armourbond™ Flash
This self-adhered base sheet is designed for flashing details. Armourbond Flash combines an approximate thickness of 2.5 mm with glass-reinforced polyester reinforcement. Its microperforated top film and removable underside release liner support installation, including on flame-sensitive areas of the substrate.
Explore this product
Universal Corner — Moulded TPO
Universal moulded TPO corner for finishing corner details on TPO membrane roofs. This preformed piece provides a dedicated shape for these connections, complementing other detailing components. The product is supplied in boxes of twenty-four units.
Explore this product
SOPRAFLASH STICK
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with a fibreglass mat. It is installed using its self-adhesive underside. The top surface is covered with fine sand, while the underside has a silicone release film. It is also suitable for flashing applications.
Explore this product
Armourbond™ Flash HD
Armourbond Flash HD provides composite reinforcement for self-adhered base-sheet flashings. Polyester is reinforced with a crossed glass scrim and embedded in SBS bitumen. This approximately 2.5 mm membrane has a microperforated surface film and a removable liner beneath the adhesive side. It is suitable for flame-sensitive areas.
Explore this product
4.5" T-Joint Cover — Moulded TPO
Round 4.5-inch moulded TPO piece designed to cover T-joints in membranes. This preformed component provides a consistent shape for detailing seam intersections. The catalogue specifies boxes of one hundred units.
Explore this product
SOPRAFLASH STICK DUO
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with a fibreglass mat. It is installed using its self-adhesive underside. The top surface is covered with fine sand, while the underside has a silicone release film. It is also suitable for flashing applications.
Explore this product
Armourbond™ Flash Sand
Armourbond Flash Sand is a sand-surfaced self-adhered base sheet for applications on flame-sensitive substrates. Approximately 2.5 mm thick, it combines glass-reinforced polyester reinforcement with an SBS binder. A silicone release film protects the adhesive side until the membrane is installed.
Explore this product
SOPRAPLY STICK DUO
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed using its self-adhesive underside. The top surface is covered with fine sand, while the underside has a silicone release film. It is also suitable for flashing applications.
Explore this product
Armourbond™ Flash Sand HD
The HD version of Armourbond Flash Sand provides an approximately 3.0 mm self-adhered base sheet for flashing details. Its composite reinforcement combines polyester with a crossed glass scrim. The top surface is sanded, while a removable silicone film protects the adhesive underside. It is intended for flame-sensitive flashing areas.
Explore this product
SOPRASTAR GR
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed with adhesive or hot-applied SEBS bitumen. Granules protect the top surface, while the underside is surfaced with fine sand. Its stated solar reflectance index is 90.
Explore this product
Armourvent™ Base
Armourvent Base uses discontinuous bitumen strips to allow moisture to disperse beneath the roof covering. This self-adhered base sheet is partially bonded to the substrate to help limit condensation-related blistering. Its side lap is self-adhered, and its heat-fusible top film allows it to receive a torch-applied cap sheet.
Explore this product
SOPRALENE 250 FR GR
This roofing cap sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed with hot-applied SEBS bitumen. Granules protect the top surface, while the underside is surfaced with fine sand.
Explore this product
Modiflex™ MP-250-Cap
Modiflex MP-250-Cap serves as the cap sheet in an SBS assembly or as protection for a built-up roof. Its glass-filament-reinforced polyester reinforcement is coated with modified bitumen. The granulated surface protects against UV exposure, while the sanded underside allows installation in hot asphalt or an IKO-approved cold adhesive.
Explore this product
ELASTOPHENE 180 PS DG
ELASTOPHENE 180 PS DG is an SBS-modified bitumen base sheet installed by nailing. Its non-woven polyester reinforcement and two selvedge edges distinguish this product. It is designed for roofing assemblies and must be installed in accordance with the manufacturer’s technical data sheet.
Explore this product
Modiflex™ MF-95-FS-Base
Modiflex MF-95-FS-Base is an SBS base sheet with non-woven fibreglass reinforcement. With a microperforated film top surface and a sanded underside, it is designed for fully adhered installation in hot asphalt or an IKO-approved cold adhesive. It forms part of a multi-ply roof covering in accordance with system specifications.
Explore this product
SOPRAWALK
SOPRAWALK is a membrane designed for walkway areas on two-ply roofs. It is installed by torch application. This product is specifically intended for access routes over the waterproofing assembly; installation requirements and integration details are set out in its technical documentation.
Explore this product
Modiflex™ MP-180-FS-Base
Modiflex MP-180-FS-Base is an SBS base sheet with glass-filament-reinforced polyester reinforcement. With a microperforated film top surface and a sanded underside, it is designed for fully adhered installation in hot asphalt or an IKO-approved cold adhesive. It forms part of a multi-ply roof covering in accordance with system specifications.
Explore this product
COLPLY BASE 410 FLEX
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed with adhesive or hot bitumen. Both faces are surfaced with fine sand. It can also serve as a vapour barrier. This version retains its flexibility at low temperatures.
Explore this product
Modiflex™ MP-180-FS-Base (3.0 mm)
Modiflex MP-180-FS-Base (3.0 mm) is an SBS base sheet with glass-filament-reinforced polyester reinforcement. With a microperforated film top surface and a sanded underside, it is designed for fully adhered installation in hot asphalt or an IKO-approved cold adhesive. It forms part of a multi-ply roof covering in accordance with system specifications.
Explore this product
Elastomeric - Pre-Flash™ Summum Drain 12"H
A 12-inch-high Pre-Flash™ drainage assembly combining a prefabricated drain, a cast aluminium strainer and a flow-control device with two adjustable gates. Its universal anchoring system brings the drainage detail components together. This version is intended for SBS elastomeric assemblies; membrane and dimensions are selected to suit the roofing detail.
Explore this product
COLVENT BASE 840
COLVENT BASE 840 is an SBS base sheet reinforced with a fibreglass mat. Its spaced adhesive strips provide partial adhesion, rather than continuous bonding over the entire surface. This self-adhesive design distinguishes it from base sheets bonded across their full underside.
Explore this product
Modiflex™ MP-HD-FS-Base
Modiflex MP-HD-FS-Base is an SBS base sheet with polyester and crossed glass scrim composite reinforcement. With a microperforated film top surface and a sanded underside, it is designed for fully adhered installation in hot asphalt or an IKO-approved cold adhesive. It forms part of a multi-ply roof covering in accordance with system specifications.
Explore this product
ELASTOPHENE 1500
This roofing base sheet uses an SBS-modified bitumen formulation. It is installed using its self-adhesive underside. The surface consists of trilaminate woven polyethylene, while the underside has a silicone release film.
Explore this product
Torchflex™ TP-250-Cap (5.0 mm)
Torchflex TP-250-Cap (5.0 mm) is a torch-applied SBS cap sheet. Its glass-reinforced polyester reinforcement supports waterproofing performance, while surface granules protect the bitumen from ultraviolet exposure. The underside film melts during application. It completes the roofing assemblies specified by IKO for this membrane.
Explore this product
TPO - Pre-Flash™ Summum Drain 12"H
A 12-inch-high Pre-Flash™ drainage assembly combining a prefabricated drain, a cast aluminium strainer and a flow-control device with two adjustable gates. Its universal anchoring system brings the drainage detail components together. This version is intended for TPO assemblies; membrane and dimensions are selected to suit the roofing detail.
Explore this product
COLPLY BASE 410
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed with adhesive or hot bitumen. Both faces are surfaced with fine sand. It can also serve as a vapour barrier.
Explore this product
Torchflex™ TP-HD-Cap
Torchflex TP-HD-Cap is a torch-applied SBS cap sheet. Its polyester and crossed glass scrim composite reinforcement supports waterproofing performance, while surface granules protect the bitumen from ultraviolet exposure. The underside film melts during application. It completes the roofing assemblies specified by IKO for this membrane.
Explore this product
COLVENT BASE 830
COLVENT BASE 830 is an SBS base sheet reinforced with a fibreglass mat. Adhesive is arranged in discontinuous strips to provide partial adhesion. Substrate requirements and application conditions specific to this membrane are set out in the SOPREMA technical data sheet.
Explore this product
Torchflex™ TF-95-FF-Base
Torchflex TF-95-FF-Base is an SBS base sheet reinforced with non-woven fibreglass. Both sides have a microperforated film: the underside film melts during torch attachment, and the top film melts when the cap sheet is installed. It is intended for the multi-ply roofing assemblies specified by IKO.
Explore this product
SOPRAFIX BASE 630
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is mechanically fastened. The top surface has a heat-fusible film, while the underside is surfaced with fine sand. Application requirements are set out in this product’s technical documentation.
Explore this product
Torchflex™ TF-95-FF-Base (2.2 mm)
Torchflex TF-95-FF-Base (2.2 mm) is an SBS base sheet reinforced with non-woven fibreglass. Both sides have a microperforated film: the underside film melts during torch attachment, and the top film melts when the cap sheet is installed. It is intended for the multi-ply roofing assemblies specified by IKO.
Explore this product
SOPRAFIX BASE 640
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is mechanically fastened. Both faces are surfaced with fine sand. Application requirements are set out in this product’s technical documentation.
Explore this product
Torchflex™ TF-95-SF-Base
Torchflex TF-95-SF-Base is an SBS base sheet with a sanded surface that helps it unroll and limits sticking within the roll. Its underside has a film that melts during torch application. This membrane can also serve as a vapour barrier, depending on the composition of the selected system.
Explore this product
SOPRAPLY BASE PLUS
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed by torch application. Both the top surface and the underside have a heat-fusible film. Application requirements are set out in this product’s technical documentation.
Explore this product
Torchflex™ TF-95-SF-Base (3.0 mm)
Torchflex TF-95-SF-Base (3.0 mm) is an SBS base sheet with a sanded surface that helps it unroll and limits sticking within the roll. Its underside has a film that melts during torch application. This membrane can also serve as a vapour barrier, depending on the composition of the selected system.
Explore this product
TPO - Pre-Flash™ Laminated Liquid Sealant Pocket
TPO liquid sealant pocket with a perimeter reinforced with 24-gauge galvanized sheet metal. The piece is hot-air welded into place, and its dimensions are designed to limit the amount of liquid filler required. Several sizes are available to adapt the detail to different penetrations.
Explore this product
SOPRALENE 180 PS 3.0
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed with hot bitumen. The top surface has a polyolefin film, while the underside has a sanded finish.
Explore this product
Torchflex™ TP-180-FF-Base
Torchflex TP-180-FF-Base is an SBS base sheet reinforced with glass-reinforced polyester. Both sides have a microperforated film: the underside film melts during torch attachment, and the top film melts when the cap sheet is installed. It is intended for the multi-ply roofing assemblies specified by IKO.
Explore this product
SOPRALENE 180 SANDED
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed with hot bitumen. Both the top surface and the underside have a sanded finish.
Explore this product
Torchflex™ TP-180-SF-Base (3.0 mm)
Torchflex TP-180-SF-Base (3.0 mm) is an SBS base sheet with a sanded surface that helps it unroll and limits sticking within the roll. Its underside has a film that melts during torch application. This membrane can also serve as a vapour barrier, depending on the composition of the selected system.
Explore this product
SOPRAPLY BASE 510
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed with hot bitumen. The top surface has a heat-fusible film, while the underside is surfaced with fine sand.
Explore this product
Torchflex™ TP-HD-FF-Base
Torchflex TP-HD-FF-Base is an SBS base sheet reinforced with polyester and crossed glass scrim composite. Both sides have a microperforated film: the underside film melts during torch attachment, and the top film melts when the cap sheet is installed. It is intended for the multi-ply roofing assemblies specified by IKO.
Explore this product
Pre-Flash™ - Pre-Cut Elastomeric Gusset
Pre-cut elastomeric membrane gusset for consistent SBS roofing details. The listed size is 4 × 8 inches, supplied in boxes of 80 units. IKO or SOPREMA membrane options are available so the version can be matched to the installed system.
Explore this product
COLPLY TRAFFIC CAP FLEX
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed with adhesive or hot-applied SEBS bitumen. Granules protect the top surface, while the underside is surfaced with fine sand. This version retains its flexibility at low temperatures.
Explore this product
ArmourCool™ Granular TP-HD
ArmourCool Granular TP-HD provides a torch-applied SBS cap sheet with reflective granules that protect the membrane from ultraviolet exposure. Its total thickness of 5.0 mm and polyester-glass composite reinforcement meet the needs of demanding assemblies. It is used as the top layer of a two-ply system or as protection for a conventional built-up roof.
Explore this product
SOPRALENE MAMMOUTH GR
This roofing cap sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed by torch application. Granules protect the top surface, while the underside has a heat-fusible film.
Explore this product
ArmourCool™ SA-HD-Cap
ArmourCool SA-HD-Cap combines a highly solar-reflective surface with a self-adhered underside for commercial projects installed without an open flame. Polyester-glass composite reinforcement stabilizes this 5.2 mm SBS membrane. Its granules protect against UV exposure and help reduce roof temperatures in summer.
Explore this product
COLPLY TRAFFIC CAP
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed with adhesive or hot bitumen. Granules protect the top surface, while the underside is surfaced with fine sand.
Explore this product
PrevENt™ ArmourCool™ Granular TP-HD-Cap
This cap sheet combines reflective ArmourCool granules with PrevENt technology, which incorporates expanded graphite for resistance to external fire exposure. The 5.0 mm SBS membrane has polyester-glass composite reinforcement. It is torch-applied and can finish a two-ply assembly or protect a built-up system, in accordance with the manufacturer’s specifications.
Explore this product
STARTER FLAM GR
STARTER FLAM GR is a starter membrane for SBS systems. It has a granulated surface and a 100 mm selvedge edge on each side. It is installed by torch application; its configuration is intended for starting the roofing assembly and making the connections shown in the manufacturer’s details.
Explore this product
Fast-N-Stick™ 180-Base
Fast-N-Stick 180-Base is a 2.5 mm base sheet designed for mechanical attachment in Fast-N-Weld systems. Its laps have self-adhered selvedges protected by a removable film. The heat-fusible top surface receives the torch-applied cap sheet, while the sanded underside limits sticking within the roll before installation.
Explore this product
SOPRAPLY TRAFFIC CAP
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed by torch application. Granules protect the top surface, while the underside has a heat-fusible film. Application requirements are set out in this product’s technical documentation.
Explore this product
Fast-N-Stick™ HD-Base
Fast-N-Stick HD-Base uses polyester-glass composite reinforcement for mechanically attached base sheets in the Fast-N-Weld system. Adhesive selvedges maintain continuity at laps once the release liner is removed. Its top film melts when the cap sheet is torch-applied, and the sanded underside helps the membrane unroll on site.
Explore this product
SOPRAPLY TRAFFIC CAP PLUS G/P 4.0
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed by torch application. Granules protect the top surface, while the underside has a heat-fusible film. Application requirements are set out in this product’s technical documentation.
Explore this product
PrevENt™ MP-HD-Cap
PrevENt MP-HD-Cap is an SBS cap sheet that incorporates expanded graphite to improve its resistance to external fire exposure. Its polyester-glass composite reinforcement is paired with a granulated surface that protects the bitumen from UV exposure. The membrane is installed by fully adhered installation in hot asphalt or an approved cold adhesive, in accordance with IKO assembly requirements.
Explore this product
SOPRASTAR GR FLEX
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed with adhesive or hot-applied SEBS bitumen. The top surface has highly reflective granules, while the underside is surfaced with fine sand. Its stated solar reflectance index is 90. This version retains its flexibility at low temperatures.
Explore this product
PrevENt™ MP-250-Cap
PrevENt MP-250-Cap is an SBS cap sheet that incorporates expanded graphite to improve its resistance to external fire exposure. Its glass-reinforced polyester reinforcement is paired with a granulated surface that protects the bitumen from UV exposure. The membrane is installed by fully adhered installation in hot asphalt or an approved cold adhesive, in accordance with IKO assembly requirements.
Explore this product
TPO – Pre-Flash™ Laminated Scupper
Prefabricated scupper with a TPO membrane skirt fused to 24-gauge galvanized steel sheet. This construction simplifies the creation of a drainage opening through the parapet with a consistent finish. Different sizes and colours allow the piece to be matched to the roofing detail.
Explore this product
ELASTOPHENE SANDED
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with a fibreglass mat. It is installed with hot bitumen. Both faces are surfaced with fine sand.
Explore this product
PrevENt™ TP-250-Cap
PrevENt TP-250-Cap is an SBS cap sheet that incorporates expanded graphite to improve its resistance to external fire exposure. Its glass-reinforced polyester reinforcement is paired with a granulated surface that protects the bitumen from UV exposure. The membrane is installed by torch application, in accordance with IKO assembly requirements.
Explore this product
TPO - Pre-Flash™ Split Pitch Pocket
Prefabricated TPO pitch pocket in the open “Split” version. Several sizes allow selection of the piece that matches the roofing detail. Membrane manufacturer and colour options help integrate it into the selected system, with customization available from Premium Flash.
Explore this product
ELASTOPHENE PS
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with a fibreglass mat. It is installed with hot bitumen. The top surface has a polyolefin film, while the underside has a sanded finish.
Explore this product
PrevENt™ TP-HD-Cap
PrevENt TP-HD-Cap is an SBS cap sheet that incorporates expanded graphite to improve its resistance to external fire exposure. Its polyester-glass composite reinforcement is paired with a granulated surface that protects the bitumen from UV exposure. The membrane is installed by torch application, in accordance with IKO assembly requirements.
Explore this product
TPO - Pre-Flash™ Pitch Pocket
Prefabricated TPO pitch pocket in the regular version. Several sizes allow selection of the piece that matches the roofing detail. Membrane manufacturer and colour options help integrate it into the selected system, with customization available from Premium Flash.
Explore this product
ELASTOPHENE FLAM 2.2
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with a fibreglass mat. It is installed by torch application. Both the top surface and the underside have a polyolefin film.
Explore this product
ArmourStick™ HD-Base
ArmourStick HD-Base is a self-adhered SBS base sheet with composite reinforcement, designed for flameless roofing systems. Its 3.5-inch side lap allows the joint to be sealed. Once the surface release film is removed, ArmourStick HD-Cap can be installed without primer, following IKO instructions.
Explore this product
TPO – Pre-Flash™ AC 6″ (Connections Not Included)
A 6-inch Pre-Flash™ AC roof outlet, available in TPO. Configurations with one, two or four outlets allow the component to suit the planned penetrations. Connections are not included with this product and are selected separately from the manufacturer’s range.
Explore this product
ELASTOPHENE 180 SANDED
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed with hot bitumen. Both faces are surfaced with fine sand. It can also serve as a vapour barrier.
Explore this product
IKO Innovi TPO 45-mil
The Innovi TPO 45 mil membrane uses Matrix technology to resist UV exposure and weathering. Reinforced with polyester, this reflective single-ply membrane is intended for commercial roofing. It can be fully adhered or mechanically attached in accordance with specifications; IKO also includes it in its induction-welded assemblies.
Explore this product
TPO – Pre-Flash™ AC 4″ (Connections Not Included)
A 4-inch Pre-Flash™ AC roof outlet, available in TPO. Configurations with one, two or four outlets allow the component to suit the planned penetrations. Connections are not included with this product and are selected separately from the manufacturer’s range.
Explore this product
ELASTOPHENE 180 PS
This roofing base sheet uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed with hot bitumen. The top surface has a heat-fusible film, while the underside has a sanded finish.
Explore this product
IKO Innovi TPO 60-mil Minimum
The Innovi TPO 60 mil Minimum membrane uses Matrix technology to resist UV exposure and weathering. Reinforced with polyester, this reflective single-ply membrane is intended for commercial roofing. It can be fully adhered or mechanically attached in accordance with specifications; IKO also includes it in its induction-welded assemblies.
Explore this product
ELASTOPHENE HS GR
ELASTOPHENE HS GR is a cap sheet with composite reinforcement. Its high-strength SBS formulation is designed to provide elasticity, elongation and flexibility. The top surface is granulated; SOPREMA also offers an FR version for increased fire resistance.
Explore this product
IKO Innovi TPO 80-mil
The Innovi TPO 80 mil membrane uses Matrix technology to resist UV exposure and weathering. Reinforced with polyester, this reflective single-ply membrane is intended for commercial roofing. It can be fully adhered or mechanically attached in accordance with specifications; IKO also includes it in its induction-welded assemblies.
Explore this product
ELASTOPHENE FLAM HS GR
ELASTOPHENE FLAM HS GR is an SBS cap sheet with composite reinforcement and a granulated top surface. Its high-strength formulation is designed to provide improved elasticity and good flexibility. The underside has a heat-fusible film, and an FR version is available for increased fire resistance.
Explore this product
IKO Cold Gold™ Field Adhesive
Cold Gold Field is used to cold-bond approved vapour barriers and Modiflex membranes, whether base sheets or cap sheets. Its single-component, solvent-free, low-VOC formulation requires no on-site mixing. This adhesive can also hold approved aggregate when used as a surfacing coat.
Explore this product
ELASTOPHENE FLAM HS
ELASTOPHENE FLAM HS is an SBS base sheet with composite reinforcement designed for high strength. Its formulation focuses on elongation, elasticity and flexibility. Heat-fusible films protect both faces; the manufacturer specifies this product for roofing assemblies and describes installation requirements in its technical data sheet.
Explore this product
IKO Cold Gold™ Flashing Adhesive
Developed for Modiflex membrane flashings, this Cold Gold adhesive is suitable for vertical surfaces and steep slopes. It combines urethane and asphalt in a ready-to-apply, single-component product that is solvent-free and low in VOCs. It is applied with a notched trowel over the entire substrate.
Explore this product
ELASTOPHENE HS SANDED
ELASTOPHENE HS SANDED is an SBS base sheet with composite reinforcement and sand on both faces. Its high-strength formulation is designed to provide elasticity and flexibility while maintaining dimensional stability. It is selected according to the roofing assembly and the application requirements described by SOPREMA.
Explore this product
Technical data availablePolybase™ 180 Mat
PolyBase 180 is a flexible reinforcing mat for flashing details in built-up and modified bitumen roofing systems. Its uncoated polyester, combined with glass filaments, helps it conform to changes in direction and complex corners. It is incorporated into flashing assemblies specified by IKO.
Explore this product
Elastomeric - Pre-Flash™ Drain 12"H
A 12-inch-high prefabricated Pre-Flash™ drain for roof drainage. The component is prepared to reduce on-site fabrication and promote a consistent finish around the drainage point. This version is intended for SBS elastomeric assemblies; membrane and dimensions are selected to suit the roofing detail.
Explore this product
ELASTOBASE
ELASTOBASE is a waterproofing membrane for built-up roofing systems. Its non-woven polyester reinforcement is coated with oxidized bitumen. The product is installed with hot bitumen; it is listed among the components in the manufacturer’s SBS section, although it uses oxidized bitumen technology.
Explore this product
IKO S.A.M.™ Adhesive LVC
The LVC version of S.A.M. primer prepares substrates for the installation of IKO self-adhered membranes. Its solvent-based formula limits VOC content and is suitable for several surfaces, including wood, concrete and metal. It is applied by roller, brush or spray to a clean, dry substrate.
Explore this product
SOPRAGLASS 100
SOPRAGLASS 100 can serve as a base sheet or vapour barrier in a roofing assembly. The membrane combines a fibreglass mat with oxidized bitumen. The manufacturer specifies either hot-bitumen adhesion or mechanical fastening, depending on the assembly and applicable requirements.
Explore this product
IKO S.A.M.™ Adhesive
S.A.M. is a fast-drying primer that promotes adhesion of IKO self-adhered membranes, both in roofing and with AquaBarrier wall membranes. It can be used on horizontal or vertical surfaces, including wood, concrete, masonry and metal. The substrate must be clean and dry; drying time varies with ambient conditions.
Explore this product
SOPRAPLY BASE 520
This roofing base sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed by torch application. Both the top surface and the underside have a heat-fusible film. Application requirements are set out in this product’s technical documentation.
Explore this product
TorchTape™ 180-FF — Reinforcing Strips
TorchTape 180-FF is a torch-weldable SBS reinforcing strip for roofing details. Its glass-reinforced polyester reinforcement combines flexibility with moisture resistance. The films covering both sides melt during torch application. Two widths are available to match the reinforcement to the planned work.
Explore this product
SOPRASTAR STICK FR GR
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed using its self-adhesive underside. Granules protect the top surface, while the underside has adhesive protected by a release film. It contains flame-retardant additives.
Explore this product
IKOTherm™
IKOTherm boards provide insulation for single-ply, built-up and modified bitumen roofing assemblies. Their rigid polyisocyanurate foam has a glass-reinforced kraft facer. Several sizes and thicknesses allow insulation to be tailored to the project; specified installation methods include hot asphalt, cold adhesive or mechanical attachment, depending on the assembly.
Explore this product
SOPRAPLY STICK TRAFFIC CAP FR
This roofing cap sheet uses an SBS-modified bitumen formulation with composite reinforcement. It is installed using its self-adhesive underside. Granules protect the top surface, while the underside has adhesive protected by a release film. It contains flame-retardant additives.
Explore this product
IKOTherm™ - 25 PSI
IKOTherm 25 PSI is a polyisocyanurate insulation board for single-ply, built-up and SBS roofs. Its glass-reinforced kraft facer accommodates installation with cold adhesive, hot asphalt or mechanical fasteners in accordance with specifications. Several sizes and thicknesses are available to meet the building’s thermal requirements.
Explore this product
2-1 SOPRASMART ISO HD
This factory-made panel combines an SBS membrane with a high-density polyisocyanurate insulation board. The membrane has non-woven polyester reinforcement and a heat-fusible film on its top surface. It can be installed with adhesive, hot bitumen or mechanical fasteners.
Explore this product
IKOTherm™ CoverShield™
IKOTherm CoverShield serves as an insulating cover board within the roofing assembly. Its closed-cell polyisocyanurate core is faced on both sides with an inorganic, acrylic-coated glass facer. It provides higher compressive strength than conventional polyiso insulation and can be cut to fit site conditions.
Explore this product
2-1 SOPRASMART ROCK SANDED
This factory-made panel combines an SBS membrane with a high-density stone wool board. The membrane has non-woven polyester reinforcement and a sanded top surface. It can be installed with adhesive, hot bitumen or mechanical fasteners. It can also serve as a vapour barrier and thermal barrier.
Explore this product
IKOTherm™ III
IKOTherm III combines rigid polyisocyanurate foam with an inorganic glass-reinforced facer. This construction supports dimensional stability and moisture resistance. The insulation is suitable for single-ply, built-up and hot- or cold-applied modified bitumen roofs. It is available in several sizes and thicknesses to adjust thermal performance.
Explore this product
2-1 SOPRASMART ROCK
This factory-made panel combines an SBS membrane with a high-density stone wool board. The membrane has non-woven polyester reinforcement and a heat-fusible film on its top surface. It can be installed with adhesive, hot bitumen or mechanical fasteners.
Explore this product
IKOTherm™ III 25 PSI
The 25 PSI version of IKOTherm III is a polyisocyanurate insulation board with an inorganic glass-reinforced facer. Its composition is designed for moisture resistance and board stability. Lightweight to handle, it can be used in single-ply, built-up or SBS roofs and is available in different sizes and thicknesses to suit the project.
Explore this product
SOPRAVAP’R
SOPRAVAP’R serves as a vapour barrier in insulated roofing assemblies. Its SBS compound is combined with a trilaminate woven polyethylene facing. The adhesive side, protected before installation by a silicone release film, allows self-adhered installation.
Explore this product
SOPRALENE 180 SP 3,5 MM
This roofing vapour barrier uses an SBS-modified bitumen formulation reinforced with non-woven polyester. It is installed by torch application. The top surface is sanded, while the underside has a polyolefin film. Application requirements are set out in this product’s technical documentation.
Explore this product
ELASTOPHENE SP 2.2
This roofing vapour barrier uses an SBS-modified bitumen formulation reinforced with a fibreglass mat. It is installed by torch application. The top surface is sanded, while the underside has a polyolefin film. Application requirements are set out in this product’s technical documentation.
Explore this product
SOPRA-ISO SL
This insulation board has a closed-cell polyisocyanurate core with fibreglass-reinforced organic facers. All four edges are shiplapped. It can be installed with adhesive or hot bitumen, or mechanically fastened, depending on the assembly.
Explore this product
SOPRA-ISO
This insulation board has a closed-cell polyisocyanurate core with fibreglass-reinforced organic facers. It can be installed with adhesive or hot bitumen, or mechanically fastened, depending on the assembly. Available thicknesses are listed in the manufacturer’s product range.
Explore this product
TPO - Pre-Flash™ Drain 12"H - Base 24″
A 12-inch-high prefabricated Pre-Flash™ drain for roof drainage. The component is prepared to reduce on-site fabrication and promote a consistent finish around the drainage point. This version is intended for TPO assemblies; membrane and dimensions are selected to suit the roofing detail.
Explore this product
2-1 SOPRASMART ISO HD HP
This factory-made panel combines an SBS membrane with a high-density polyisocyanurate insulation board. The membrane has composite reinforcement and a heat-fusible film on its top surface. It combines the functions of base sheet, cover board and insulation in the roofing assembly.
Explore this product
TPO - Pre-Flash™ Scupper
Prefabricated Pre-Flash™ scupper for drainage details through a parapet. This TPO version reduces on-site cutting and assembly. It is available in several sizes and colours, with customization options offered by the manufacturer.
Explore this product
LASTOBOND STICK VP
LASTOBOND STICK VP is a self-adhered, vapour-permeable roofing underlayment. Its surface consists of three layers of polypropylene, while a silicone release film protects the adhesive. SOPREMA specifies primer-free installation and application at temperatures as low as −7 °C, subject to the requirements in its technical data sheet.
Explore this product
TPO - Pre-Flash™ U-Shaped Corner
Prefabricated U-shaped Pre-Flash™ corner made from TPO membrane. It provides consistent geometry for corner details while reducing on-site forming. The 6- or 12-inch sizes and colours are selected to suit the detail.
Explore this product
2-1 SOPRASMART BOARD
This factory-made panel combines an SBS membrane with a semi-rigid SOPRABOARD asphaltic board. The membrane has non-woven polyester reinforcement and a heat-fusible film on its top surface. It can be installed with adhesive, hot bitumen or mechanical fasteners.
Explore this product
TPO - Pre-Flash™ L-Shaped Corner
Prefabricated L-shaped Pre-Flash™ corner made from TPO membrane. It provides consistent geometry for corner details while reducing on-site forming. The 6- or 12-inch sizes and colours are selected to suit the detail.
Explore this product
SOPRASTOP
SOPRASTOP serves as a vapour barrier in a roofing assembly. It is made from two layers of durable kraft paper laminated together with asphalt. This product is designed for adhesive installation, according to the substrate and details specified by SOPREMA.
Explore this product
TPO - Pre-Flash™ Split Mini Cone
Pre-Flash™ mini cone made from TPO membrane in the open “Split” configuration. This prefabricated piece is used for penetration details and is available in a standard size. Several membrane manufacturers and colours are offered to create a finish that matches the selected roofing system.
Explore this product
ALSAN FLASHING WINTER
ALSAN FLASHING WINTER waterproofs flashings and details where sheet membranes are difficult to install. This waterproofing coating uses a two-component bitumen-polyurethane formulation designed for low temperatures. It is applied by brush or trowel according to the manufacturer’s specifications.
Explore this product
TPO - Pre-Flash™ Split Chimney Flashing
Prefabricated TPO chimney flashing from the “Split” range. Catalogue options include 5- and 8-inch sizes. The piece reduces on-site fabrication; select the configuration, membrane and colour to suit the connection detail.
Explore this product
ALSAN FLASHING
ALSAN FLASHING is a liquid coating for waterproofing flashings and complex details. Its single-component formulation combines bitumen and polyurethane. It addresses areas that are difficult to waterproof with sheet membranes and is applied by brush or trowel.
Explore this product
TPO - Pre-Flash™ Chimney Flashing
Prefabricated TPO chimney flashing from the regular range. Catalogue options include 5- and 8-inch sizes. The piece reduces on-site fabrication; select the configuration, membrane and colour to suit the connection detail.
Explore this product
DUOTACK
DUOTACK is a two-component, low-rise polyurethane adhesive. It bonds insulation, cover boards and thermal barriers in roofing assemblies. Substrate selection, application equipment and application quantities are governed by SOPREMA’s technical instructions.
Explore this product
2-1 SOPRASMART ISO HD HP SANDED
This factory-made panel combines an SBS membrane with a high-density polyisocyanurate insulation board. The membrane has composite reinforcement and a sanded top surface. It combines the functions of base sheet, cover board and insulation in the roofing assembly.
Explore this product
TPO - Pre-Flash™ Square Split Post Cover
Prefabricated TPO post cover in a “Split” configuration for a square post. The catalogue lists a 4-inch size. Membrane and colour choices allow the detail to match the building’s roof.
Explore this product
SOPRA-ISO PLUS TRANSITION BOARD
SOPRA-ISO PLUS TRANSITION BOARD starts a slope without the usual added thickness of traditional boards. The manufacturer offers 4 ft by 4 ft polyisocyanurate boards with slopes of 2% or 4%, tapering to 0 in. at their thinnest point.
Explore this product
TPO - Pre-Flash™ Round Split Post Cover
Prefabricated TPO post cover in a “Split” configuration for a round post. This model comes in a standard size; the fastener is not included. Membrane and colour choices allow the detail to match the roof.
Explore this product
LASTOBOND 195
LASTOBOND 195 is self-adhered protection for eaves beneath shingles. Its SBS compound is reinforced with a fibreglass mat and serves as an air and vapour barrier. It is incorporated as roofing underlayment according to the installation details and substrate requirements specified by SOPREMA.
Explore this product
TPO - Pre-Flash™ Liquid Sealant Pocket
Prefabricated TPO pocket designed to hold liquid sealant around a penetration detail. A 5.5-inch size is among the options listed in the catalogue. Membrane and colour variants allow selection of a piece that matches the roof.
Explore this product
LASTOBOND 240
LASTOBOND 240 is installed beneath shingles to protect the eaves. This self-adhered roofing underlayment combines fibreglass mat reinforcement with an SBS formulation and serves as an air and vapour barrier. Substrate preparation and connections follow the instructions specific to this product.
Explore this product
TPO - Pre-Flash™ Insulated Vent
Pre-insulated Pre-Flash™ vent with TPO cladding and a painted aluminium cap. Its one-size design is adjustable from 3 to 6 inches. Factory preparation simplifies the ventilation detail, while membrane and colour options allow it to match the system.
Explore this product
LASTOBOND SHIELD
LASTOBOND SHIELD is a self-adhered underlayment for shingle roofs. Its composition combines SBS bitumen with a trilaminate woven polyethylene facing. The membrane also serves as an air and vapour barrier, with detailed installation requirements in SOPREMA’s documentation.
Explore this product
LASTOBOND SHIELD HT
LASTOBOND SHIELD HT is a self-adhered membrane designed for roofing underlayment. Its formulation is based on SBS bitumen. It is selected according to the intended roof covering and substrate; its technical data sheet specifies application temperatures, connections and other product-specific requirements.
Explore this product
SOPRA-ISO TAPERED
This insulation board has a closed-cell polyisocyanurate core with fibreglass-reinforced organic facers. Its tapered shape helps create a slope to direct water and reduce ponding on the roof. It can be installed with adhesive or hot bitumen, or mechanically fastened, depending on the assembly.
Explore this product
SOPRAGUARD TAPE
SOPRAGUARD TAPE is a self-adhered membrane intended to act as a flame barrier. It combines a fibreglass mat with SBS bitumen. This accessory is part of SOPREMA’s roofing components; its placement and overlap width must comply with the manufacturer’s installation details.
Explore this product
SOPRAMASTIC
SOPRAMASTIC is used to form joints and caulk bituminous membranes. This black mastic combines an SBS formulation, fibres, mineral fillers and a solvent. Approved substrates, application requirements and finishing details are set out in the product’s documentation.
Explore this product
COLPLY FLASHING
COLPLY FLASHING is an SBS bituminous adhesive for bonding membranes on flashings and surfaces with slopes greater than 3%. It provides a formulation suited to these roof areas. Substrate and application requirements are set out in its technical data sheet.
Explore this product
SOPRALAP SANDED
SOPRALAP SANDED is an SBS strip with composite reinforcement and sand on both faces. It seals transverse laps in composite panels and can be used with sand-surfaced base sheets. Its role is to maintain waterproofing continuity at connections requiring a cover strip.
Explore this product
SOPRALAP STICK
SOPRALAP STICK is a self-adhered cover strip for connections in the waterproofing assembly. It combines composite reinforcement with an SBS formulation. Its use depends on the membranes and joint details specified by SOPREMA; preparation and installation requirements are detailed in its technical data sheet.
Explore this product
SOPRALAP
SOPRALAP is an SBS strip with composite reinforcement installed by torch application. It is designed to waterproof transverse laps in certain SOPREMA products. Compatible products and required overlap dimensions must be selected using the technical details specific to the assembly.
Explore this product
COLPLY
COLPLY is a bituminous adhesive for SBS membranes on surfaces with slopes below 3%. This product is intended for bonding the low-slope roof field. For flashings or steeper slopes, SOPREMA recommends the separate COLPLY FLASHING formulation.
Explore this product
SOPRASPHALTE M
SOPRASPHALTE M is an SEBS-modified bitumen for hot bonding SBS roofing membranes. It acts as an adhesive in the waterproofing assembly. Application temperatures, coverage rates and substrate requirements are defined in its technical documentation.
Explore this product
SOPRASOLIN HD
SOPRASOLIN HD is a self-adhered SBS membrane protected by an aluminum sheet. It serves as an air and vapour barrier at waterproofing details. Uses include connections around vents, ducts, skylights and chimneys, according to the details specified by SOPREMA.
Explore this product
SOPRAJOINT
SOPRAJOINT is a membrane designed to waterproof expansion joints. It combines a polyester knit with an SBS formulation. This product has a specific role in building details; its configuration and connections must follow the manufacturer’s technical specifications.
Explore this product
SOPRA-ISO PLUS SL
This insulation board has a closed-cell polyisocyanurate core with polymer-coated fibreglass facers. All four edges are shiplapped. It can be installed with adhesive or hot bitumen, or mechanically fastened, depending on the assembly.
Explore this product
SOPRAROCK DD
SOPRAROCK DD is an insulation board made from stone wool. It has a rigid top surface, and the manufacturer specifies mechanical fastening. It contributes to the insulation of the roofing assembly, with thickness and assembly selected to suit the project.
Explore this product
SOPRAROCK DD PLUS
SOPRAROCK DD PLUS is a stone wool insulation board with a rigid, bitumen-impregnated surface. The manufacturer allows installation with adhesive or hot bitumen, as well as mechanical fastening. The selected method depends on the roofing assembly and its technical specifications.
Explore this product
SOPRA-ISO PLUS
This insulation board has a closed-cell polyisocyanurate core with polymer-coated fibreglass facers. It can be installed with adhesive or hot bitumen, or mechanically fastened, depending on the assembly. Available thicknesses are listed in the manufacturer’s product range.
Explore this product
SOPRA-XPS 35
SOPRA-XPS 35 is rigid, closed-cell extruded polystyrene insulation. Intended in particular for inverted protected-membrane roofs, it is available with square or shiplapped edges. SOPREMA states that it meets Type 4 requirements under CAN/ULC S701.1.
Explore this product
SOPRA-XPS 35 DC
SOPRA-XPS 35 DC is extruded polystyrene insulation intended in particular for inverted roofs. It has drainage channels on one face and around the perimeter. Its foam is closed-cell, its edges can be square or shiplapped, and the product meets Type 4 requirements under CAN/ULC S701.1.
Explore this product
2-1 SOPRASMART ISO HD SANDED
This factory-made panel combines an SBS membrane with a high-density polyisocyanurate insulation board. The membrane has non-woven polyester reinforcement and a sanded top surface. It can be installed with adhesive, hot bitumen or mechanical fasteners.
Explore this product
SOPRA-ISO PLUS HD
SOPRA-ISO PLUS HD combines the functions of thermal insulation and cover board. Its high-density, closed-cell polyisocyanurate core is protected by fibreglass-reinforced organic facers. This board is designed to support membranes on low-slope roofs.
Explore this product
2-1 SOPRASMART BOARD SANDED
This factory-made panel combines an SBS membrane with a semi-rigid SOPRABOARD asphaltic board. The membrane has non-woven polyester reinforcement and a sanded top surface. It can be installed with adhesive, hot bitumen or mechanical fasteners.
Explore this product
SOPRA-ISO PLUS HINGED SUMP
SOPRA-ISO PLUS HINGED SUMP is an 8 ft by 8 ft component designed to form a low point around a drain. It is installed in one step on conventional insulated roofs. Its geometry promotes flow towards the drain, with or without a structural slope in the deck.
Explore this product
SOPRA-ISO PLUS PRE-CUT CRICKET FOR MECHANICAL UNITS
The SOPRA-ISO PLUS PRE-CUT CRICKET FOR MECHANICAL UNITS helps water flow around rooftop obstacles. It is intended in particular for mechanical units and roof access hatches. Printed cut lines indicate the adjustments needed for the length of the equipment being served.
Explore this product
SOPRA-ISO PLUS SUMP
SOPRA-ISO PLUS SUMP is a 4 ft by 4 ft component that creates a low point near a drain. It promotes local drainage on conventional insulated roofs. The product is installed in one step and can be used on flat decks or decks with a structural slope.
Explore this product
SOPRA-ISO PLUS TAPERED
This insulation board has a closed-cell polyisocyanurate core with polymer-coated fibreglass facers. Its tapered shape helps create a slope to direct water and reduce ponding on the roof. It can be installed with adhesive or hot bitumen, or mechanically fastened, depending on the assembly.
Explore this product
SOPRA-ISO PLUS HINGED PRE-CUT CRICKET
The SOPRA-ISO PLUS HINGED PRE-CUT CRICKET directs water towards drains and scuppers. Its angles are set and its cuts made at the factory to limit on-site adjustments. It is one of the tapered components available to organize drainage within the roofing assembly.
Explore this product
SOPRA-ISO HINGED PRE-CUT CRICKET
The SOPRA-ISO HINGED PRE-CUT CRICKET helps create drainage paths towards drains and scuppers. Its manufacture with predefined angles is intended to reduce cutting on site. Its configuration is selected as part of the tapered roofing system design.
Explore this product
ELASTOCOL STICK H2O
ELASTOCOL STICK H2O prepares substrates for self-adhered membranes. This primer is based on a polymer emulsion and is intended to improve adhesion to many substrates. SOPREMA offers it particularly for situations where solvent-based preparation is not recommended.
Explore this product
ELASTOCOL STICK
ELASTOCOL STICK is a primer for self-adhered membranes and porous substrates. Its formulation contains SBS rubbers, adhesion-promoting resins and volatile solvents. Depending on the format and technical instructions, it can be applied by aerosol, brush or roller.
Explore this product
ELASTOCOL STICK ZERO
ELASTOCOL STICK ZERO promotes the adhesion of self-adhered membranes to most substrates specified by the manufacturer. It combines synthetic polymers, adhesive resins and volatile solvents. The specified application is by brush or roller, after surface preparation in accordance with its technical data sheet.
Explore this product
ELASTOCOL 350
ELASTOCOL 350 prepares surfaces before the installation of torch-applied membranes. This primer is a water-based bitumen emulsion and provides an option where solvent-based products are not recommended. It can be applied by brush, roller or spray according to the instructions.
Explore this product
ELASTOCOL 500
ELASTOCOL 500 is a bituminous primer that promotes the adhesion of torch-applied membranes to metal or concrete. Its formulation includes volatile solvents and adhesion additives. The manufacturer specifies several application methods, including aerosol, brush, roller and spray gun.
Explore this product
SOPRABOARD
SOPRABOARD is an asphaltic board consisting of a mineral-filled reinforced core between two asphalt-saturated fibreglass mats. It can be installed with hot bitumen, DUOTACK adhesive or mechanical fasteners. The installation method is selected according to the roofing assembly and existing substrate.
Explore this product
ALSAN SIL 402
ALSAN SIL 402 is a single-component, high-solids silicone liquid coating. It protects metal roofs exposed to the weather. This finish is part of the manufacturer’s protective system, with preparation and application requirements specified in the technical data sheet.
Explore this product
ALSAN AC 180
ALSAN AC 180 prepares various metals before application of the coating system. This single-component, water-based acrylic primer is intended in particular for Galvalume, galvanized steel and aluminum. Its formulation inhibits rust; cleaning and application requirements are defined by SOPREMA.
Explore this product
ALSAN PU 410
ALSAN PU 410 is a single-component polyurethane resin used as a topcoat. It is part of roofing systems that protect against the weather. The manufacturer associates these systems with high solar reflectance; performance depends on the assembly, substrate and correct installation.
Explore this product
ALSAN PU 310
ALSAN PU 310 is the single-component polyurethane base coat in roofing weather-protection systems. It is applied before the finish specified by the manufacturer. Its preparation, application thickness and substrate compatibility must follow the specifications of the selected system.
Explore this product
SOPRAFLOW ALU NC Drains
SOPRAFLOW ALU NC drains collect rainwater on new roofs. They have an aluminum body. The mechanically clamped SOPRAFLOW ALU STRAINER and SOPRAFLOW POLE MARKER are separate accessories required to complete the assembly described by the manufacturer.
Explore this product
SOPRAFLOW ALU RF Drains
SOPRAFLOW ALU RF drains are designed to remove water from flat roofs being reroofed. Installation requires the SOPRAFLOW SEAL compression seal. The mechanically clamped aluminum strainer and marker pole are selected separately to complete the system.
Explore this product
SOPRAMASTIC BLOCKS
SOPRAMASTIC BLOCKS are the premoulded polyester blocks in the SOPRAMASTIC BLOCK system. They form details around penetrations. Assembly must use the mastics and substrate conditions specified by SOPREMA to create the sealing system as designed.
Explore this product
SOPRAMASTIC PF
SOPRAMASTIC PF is a single-component, moisture-curing polyether sealant. It is intended for horizontal surfaces in the SOPRAMASTIC BLOCK system. It is used around penetrations and details with the other components specified in the installation documentation.
Explore this product
BULK GRANULES
BULK GRANULES are coloured ceramic granules intended for roof finishing. This product is listed among SOPREMA accessories. Colour selection and the areas to be treated are determined by the membrane, finishing details and project-specific requirements.
Explore this product
SOPRAMASTIC SP2
SOPRAMASTIC SP2 combines the functions of adhesive and sealant. This single-component polyether product cures with moisture. It bonds SOPRAMASTIC blocks to one another and to the substrate on horizontal or vertical surfaces when sealing penetrations and details.
Explore this product
SOPRAMASTIC ALU
SOPRAMASTIC ALU is an aluminum-coloured mastic for jointing and caulking bituminous membranes. Its formulation combines SBS, fibres, mineral fillers and a solvent. Substrate requirements and application details are defined in its technical documentation.
Explore this product
POLYFLEECE
POLYFLEECE is a non-woven polyester reinforcement for ALSAN FLASHING and COLPHENE LM BARR products. It is unrolled over the base resin to reinforce the application. Overlaps and saturation must follow the installation details for the selected liquid system.
Explore this product
SOPRATACK FLASHING
SOPRATACK FLASHING is a two-component polyurethane adhesive described as odourless. It bonds SBS membranes to flashings and surfaces with slopes greater than 3%. This formulation is intended for the detail areas and slopes covered by its technical data sheet.
Explore this product
SOPRATACK FLASHING WINTER
SOPRATACK FLASHING WINTER is a two-component polyurethane formulation for bonding SBS membranes. It is intended for flashings and surfaces with slopes greater than 3%. The WINTER version is selected according to site conditions and the temperatures specified in its technical documentation.
Explore this product
SOPRATACK WINTER
SOPRATACK WINTER is a two-component polyurethane adhesive for SBS membranes. The specified installation method uses a notched squeegee. Temperatures, mixing ratios and substrate requirements for this version must be checked in its technical data sheet before application.
Explore this product
COLPLY EF FLASHING CEMENT
COLPLY EF FLASHING CEMENT is a solvent-free polyether adhesive for SBS membranes. It is intended for surfaces with slopes greater than 3%. The manufacturer specifies application with a notched squeegee; installation parameters and approved substrates are set out in its technical documentation.
Explore this product
COLPLY EF
COLPLY EF is a solvent-free polyether adhesive for SBS membranes on surfaces with slopes below 3%. It is applied with a notched squeegee. This product is intended for low-slope areas, while details or steeper slopes require the formulation specified by the manufacturer.
Explore this product
SOPRASPHALTE OX TYPE II
SOPRASPHALTE OX TYPE II is an oxidized bitumen supplied in bulk and used as a hot-applied adhesive. It bonds roofing membranes, cover boards and insulation. SOPREMA specifies a slope range of 1 to 2% under CSA A123.4.
Explore this product
SOPRASPHALTE OX TYPE III
SOPRASPHALTE OX TYPE III is an oxidized bitumen supplied in bags for hot bonding. It secures waterproofing membranes, cover boards and insulation. The intended applications have slopes of 1 to 25%, in accordance with the CSA A123.4 reference cited by SOPREMA.
Explore this product
SOPRATACK
SOPRATACK is a two-component polyurethane adhesive for bonding SBS membranes. According to SOPREMA, its formulation has a very low volatile organic compound content. Mixing ratios, substrates and application requirements are described in the product’s technical data sheet.
Explore this product
SOPRAFELT NO. 15
SOPRAFELT NO. 15 is a perforated felt for waterproofing traditional built-up roofing systems. It combines flexible, durable reinforcement with asphalt-impregnated organic fibres. Printed surface guides assist with installation and membrane positioning within the assembly.
Explore this product
ELASTOCOL 190
ELASTOCOL 190 prepares exterior surfaces before the installation of self-adhered membranes. This primer contains SBS rubbers, adhesive resins and solvents and is intended in particular for concrete, metal, wood and plywood. It is also available in aerosol form; temperatures and storage requirements are set out in its technical data sheet.
Explore this product
ALSAN SIL 902 FLASHING
ALSAN SIL 902 FLASHING is a single-component silicone sealant used to prepare metal roofs. It treats joints, penetrations and fasteners before application of ALSAN SIL 402 coating. The manufacturer specifies brush or trowel application depending on the detail being completed.
Explore this product
SOPRALASTIC 123
SOPRALASTIC 123 is an elastomeric bitumen coating for restoring the protection of existing asphalt roofs or metal surfaces. Its formulation contains mineral fillers and solvents. It must always receive additional protection: SOPRALASTIC 124 ALU or small gravel, as specified in the technical data sheet.
Explore this product
SOPRALASTIC 124 ALU
SOPRALASTIC 124 ALU is an aluminum-coloured reflective coating based on elastomeric bitumen. It can protect metal elements against corrosion and bituminous surfaces against ultraviolet radiation. Uses include protecting sanded membranes and SOPRALASTIC 123 coating.
Explore this product
Type IV Fibreglass Felt
This built-up roofing felt combines a non-woven fibreglass reinforcement with oxidized asphalt saturation. Its inorganic structure resists moisture and provides reinforcement in both directions of the roll. It is used in assemblies including the conventional four-ply systems described by IKO.
Explore this product
Type 2 Asphalt
Type 2 oxidized bitumen acts as a binder and waterproofing material in compatible roofing assemblies. IKO specifies it for organic or fibreglass felts, modified bitumen membranes and cover boards. It is available as bulk liquid or in kegs for the low-slope applications covered by its documentation.
Explore this product
Type 3 Asphalt
IKO Type 3 asphalt is an oxidized bitumen used for waterproofing work and certain roofing assemblies. It is compatible with fibreglass felts, rolled bituminous membranes and cover boards specified for the system. The product is available as bulk liquid and in 100 lb kegs.
Explore this product
IKO Easy-Melt™
The Easy-Melt line supplies oxidized asphalt in 22.7 kg bags whose packaging melts in the kettle. IKO documents Type 2 and Type 3 versions, along with their low-odour variants. They are used in compatible roofing and waterproofing systems; allowable slope and component selection depend on the version chosen.
Explore this product
Modi-Melt™ SEBS
Modi-Melt SEBS combines asphalt with SEBS polymers to produce a flexible, elastic bituminous binder. It can be used with compatible fibreglass felts, SBS membranes, insulation and cover boards. IKO presents it as an option for its built-up systems and waterproofing applications.
Explore this product
Hot Liquid Asphalt
Oxidized asphalt supplied in liquid form for waterproofing and hot-bonding work. BP offers Types II and III at its LaSalle facilities. The type selected depends on the roofing system and its slope.
Explore this product
Asphalt in KEGS
Solid Burfalt asphalt supplied in cardboard KEGS for built-up roofing work. Types II and III are packaged in 100 lb units. BP lists availability at its Edmonton facilities.
Explore this product
No. 15 CSA Perforated Saturated Felt — RF404N
Asphalt-saturated organic felt for built-up roofs. Its perforations and guide lines help with ply installation and alignment. The RF404N roll provides roofing reinforcement for use within the specified system.
Explore this product
ESGARD High Density — Uncoated, 1/2 in.
High-density wood fibre insulation board, left uncoated on all six sides. The fibres are wax-treated to limit water absorption. It provides a substrate for membranes and hot bitumen applications.
Explore this product
ESGARD High Density — Coated on 1 Side, 1/2 in.
High-density ESGARD wood fibre roof insulation coated on one side. This 1/2-inch board contributes to the rigidity of the assembly and provides a substrate for the membrane or hot asphalt application.
Explore this product
ESGARD High Density — Coated on 6 Sides, 1/2 in.
High-density 1/2-inch ESGARD board coated on all six sides. Its structure of wax-treated wood fibres provides a substrate for membranes and hot bitumen applications within a roofing assembly.
Explore this product
ESGARD High Strength — Coated on 1 Side, 1 in.
A 1-inch ESGARD insulation board from the high-strength range, coated on one side. Its wood fibre structure provides a rigid substrate for roofing membranes and hot asphalt work.
Explore this product
ESGARD High Strength — Coated on 6 Sides, 1/2 in.
High-strength 1/2-inch ESGARD insulation, coated on all six sides. Made from wax-treated wood fibres, it provides a substrate for the membranes and hot asphalt layers of the roofing system.
Explore this product
ESGARD High Strength — Coated on 1 Side, 1/2 in.
High-strength 1/2-inch ESGARD roofing board, coated on one side. Its wax-treated wood fibre composition and strength rating make it suitable as a substrate for membranes and hot bitumen.
Explore this productNo products found.
Try another keyword or remove a filter.
Products are presented for reference. Assembly, compatibility and availability are confirmed for your project. Product pages link to manufacturer documentation.
Let’s talk about your project, priorities and next steps.
514 556-2864